Inspection Panel: Staying Safe in Your Own House
Before the very cold weather sets in, the boiler needs to be checked for safety reasons. However, it is now required that the flue should have a full visual access. This means that the whole length of the flue needs to be seen. This may mean that there must be access in the other rooms of your house. You will need a flue inspection panel for this.
The safety engineer, upon doing the annual check-up of your boiler will need to confirm the following things: effectiveness of the flue, combustion supply, operating pressure or heat input of the boiler, safe functioning of the appliance. It is important to visually check the boiler to fully determine the safety. When the safety engineer is not able to access the flue to check the necessary things, it can pose a problem since everything needs to be seen.
Without full visualization of the boiler, there could be leaks and malfunctioning that are not detected. This can be very dangerous. Carbon monoxide can leak into the room which can be fatal. A malfunctioning boiler can lead to fires.
In installing an inspection hatch, there are things to be considered such as the ceiling composites and building regulations. An initial survey of the place must be done before installation. After installation, the current fire and smoke rating of the building must be retained and that there is no compromise of the building structure in any way.
The inspection panels must be at least 300mm x 300mm and must be installed within 1.5 metres of any bends. This may not always be the case so safety engineers will come up with the best solution to meet the standards.
It is important that the inspection panel you choose has a high quality. It has to be able to access all the concealed areas in your ceiling and wall where fire rating is required.
There are boilers that are located on an outside wall. If this is your case, then there is nothing to worry about during inspection because the engineer can see the entire flue. Flats and apartments have boiler flues and these cannot be readily inspected since they are hidden behind the walls and the ceilings of the place. If you are living in this type of house, then you have to be aware of some things. Gas Safe engineers need to see the flue as part of the routine check. Carbon monoxide poisoning is possible if the boiler is not working properly.
It is not enough that you have carbon monoxide detectors. The flue still needs inspection and you may have to have inspection hatches fitted. Make sure that these hatches are fitted as soon as possible.
You may be worried about the expenses that will be incurred during this time. However, if you think about it, this is just a small price to pay in exchange for the safety of your family. Injury can be avoided as long as the safety standards are observed and the guidelines followed.
The safety engineer, upon doing the annual check-up of your boiler will need to confirm the following things: effectiveness of the flue, combustion supply, operating pressure or heat input of the boiler, safe functioning of the appliance. It is important to visually check the boiler to fully determine the safety. When the safety engineer is not able to access the flue to check the necessary things, it can pose a problem since everything needs to be seen.
Without full visualization of the boiler, there could be leaks and malfunctioning that are not detected. This can be very dangerous. Carbon monoxide can leak into the room which can be fatal. A malfunctioning boiler can lead to fires.
In installing an inspection hatch, there are things to be considered such as the ceiling composites and building regulations. An initial survey of the place must be done before installation. After installation, the current fire and smoke rating of the building must be retained and that there is no compromise of the building structure in any way.
The inspection panels must be at least 300mm x 300mm and must be installed within 1.5 metres of any bends. This may not always be the case so safety engineers will come up with the best solution to meet the standards.
It is important that the inspection panel you choose has a high quality. It has to be able to access all the concealed areas in your ceiling and wall where fire rating is required.
There are boilers that are located on an outside wall. If this is your case, then there is nothing to worry about during inspection because the engineer can see the entire flue. Flats and apartments have boiler flues and these cannot be readily inspected since they are hidden behind the walls and the ceilings of the place. If you are living in this type of house, then you have to be aware of some things. Gas Safe engineers need to see the flue as part of the routine check. Carbon monoxide poisoning is possible if the boiler is not working properly.
It is not enough that you have carbon monoxide detectors. The flue still needs inspection and you may have to have inspection hatches fitted. Make sure that these hatches are fitted as soon as possible.
You may be worried about the expenses that will be incurred during this time. However, if you think about it, this is just a small price to pay in exchange for the safety of your family. Injury can be avoided as long as the safety standards are observed and the guidelines followed.
Source...