10 Power Tools that Need Maintenance(1)
1: Electric Hand Drill
The electric hand drill may very well be the most overworked of all tools. It doesn't just drill holes; attachments allow it to also polish, sand and grind. Due to its frequent usage, maintenance is especially important. Drill bits should always be sharp. So, either sharpen or replace them when required. If you're using the drill for extended periods of time, allow it to cool down every so often to avoid overheating. Other ways to prevent this problem include keeping the air vents and the motor clean by blowing compressed air on them. Use a toothbrush to remove stubborn, dirty patches from the engine's fan. When you're done using it, wipe down the drill with a clean cloth dampened with a household detergent. Also, you should coat metal surfaces with a light film of oil using a soft cloth to keep these areas clean. If your hand drill is cordless, remember to recharge the RYOBI 1400652 power tool battery(Ni-Cd 12.00V 1400.00mAh) when necessary so it's ready when you need it next.
2: Power Sander
There are a couple kinds of power sanders. Whichever one you have, follow these maintenance tips to ensure your tool (BOSCH PST 14.4V power tool battery )stays in great shape for a long time. Sanders accumulate dust quickly. When grime gunks up internal mechanisms or builds up on the fan, your sander can overheat and stop working. To prevent this, regularly clean the fan and remove dust from the air openings using a brush, compressed air or simply filling your lungs with air and blowing on those areas. To prevent filth from accumulating and obstructing the fan, always use the dust bag and empty it often before it's full. After each use, clean the sander by first removing the sandpaper, then blowing compressed air over it and out of vents and openings. Gently scrub stubborn dirty spots with an old toothbrush. Always ensure the sandpaper is aligned correctly; if it's off, sparks may fly from the platen assembly, or the sandpaper might veer to one side or slide off. And of course, clean and replace sandpaper as needed.
3: Drill Press
Unlike the power sanders we just discussed, drill presses come in many sizes that represent hand-held, bench and floor models. They all benefit from the same kind of care. To prevent rusting, wipe down the table and all metal areas with oil or a relatively thin, moisture-resistant sealant called paste wax. Also, apply paste wax to stationary surfaces. If you use a drill press often, check the front bearings once a month and the motor oil cups twice a year in order to find problems when they're nascent, rather than full-blown, bigger headaches. Drip No. 20 SAE oil into bearing slots.
4: Saber Saw
The saber saw, also called a jig saw, is most recognized for its ability to maneuver tight corners and cut curves in wood. But it can cut through other materials, too, such as metal, drywall, rubber, leather and asphalt. Most problems people have with this machine are caused by their misuse of it. Poor practices often make it overheat and eventually burn out prematurely. Let the motor reach maximum speed before engaging the blade in the work piece. Adjust the speed according to your material: faster for softer surfaces, slower for hard mediums. If you notice spots with wood burns, it's time to sharpen the blade. If you don't have the right tools (DEWALT DW945 power tool battery), hire a pro to sharpen it for you. Sharp blades are important. Dull ones can cause the motor to overheat, lose power or stop working altogether. Blunted blades also can make the saw rattle excessively or bend, break or jam. Eventually, when sharpening a blade doesn't make it sharp enough, just replace it. Unplug the saw after each use, and use a toothbrush to clean the roller, collar and base of the blade shaft assembly. Using compressed air, blow air through vents. Remember to service the blade shaft assembly annually.
RYOBI 1400652 power tool battery(Ni-Cd 12.00V 1400.00mAh)
The electric hand drill may very well be the most overworked of all tools. It doesn't just drill holes; attachments allow it to also polish, sand and grind. Due to its frequent usage, maintenance is especially important. Drill bits should always be sharp. So, either sharpen or replace them when required. If you're using the drill for extended periods of time, allow it to cool down every so often to avoid overheating. Other ways to prevent this problem include keeping the air vents and the motor clean by blowing compressed air on them. Use a toothbrush to remove stubborn, dirty patches from the engine's fan. When you're done using it, wipe down the drill with a clean cloth dampened with a household detergent. Also, you should coat metal surfaces with a light film of oil using a soft cloth to keep these areas clean. If your hand drill is cordless, remember to recharge the RYOBI 1400652 power tool battery(Ni-Cd 12.00V 1400.00mAh) when necessary so it's ready when you need it next.
2: Power Sander
There are a couple kinds of power sanders. Whichever one you have, follow these maintenance tips to ensure your tool (BOSCH PST 14.4V power tool battery )stays in great shape for a long time. Sanders accumulate dust quickly. When grime gunks up internal mechanisms or builds up on the fan, your sander can overheat and stop working. To prevent this, regularly clean the fan and remove dust from the air openings using a brush, compressed air or simply filling your lungs with air and blowing on those areas. To prevent filth from accumulating and obstructing the fan, always use the dust bag and empty it often before it's full. After each use, clean the sander by first removing the sandpaper, then blowing compressed air over it and out of vents and openings. Gently scrub stubborn dirty spots with an old toothbrush. Always ensure the sandpaper is aligned correctly; if it's off, sparks may fly from the platen assembly, or the sandpaper might veer to one side or slide off. And of course, clean and replace sandpaper as needed.
3: Drill Press
Unlike the power sanders we just discussed, drill presses come in many sizes that represent hand-held, bench and floor models. They all benefit from the same kind of care. To prevent rusting, wipe down the table and all metal areas with oil or a relatively thin, moisture-resistant sealant called paste wax. Also, apply paste wax to stationary surfaces. If you use a drill press often, check the front bearings once a month and the motor oil cups twice a year in order to find problems when they're nascent, rather than full-blown, bigger headaches. Drip No. 20 SAE oil into bearing slots.
4: Saber Saw
The saber saw, also called a jig saw, is most recognized for its ability to maneuver tight corners and cut curves in wood. But it can cut through other materials, too, such as metal, drywall, rubber, leather and asphalt. Most problems people have with this machine are caused by their misuse of it. Poor practices often make it overheat and eventually burn out prematurely. Let the motor reach maximum speed before engaging the blade in the work piece. Adjust the speed according to your material: faster for softer surfaces, slower for hard mediums. If you notice spots with wood burns, it's time to sharpen the blade. If you don't have the right tools (DEWALT DW945 power tool battery), hire a pro to sharpen it for you. Sharp blades are important. Dull ones can cause the motor to overheat, lose power or stop working altogether. Blunted blades also can make the saw rattle excessively or bend, break or jam. Eventually, when sharpening a blade doesn't make it sharp enough, just replace it. Unplug the saw after each use, and use a toothbrush to clean the roller, collar and base of the blade shaft assembly. Using compressed air, blow air through vents. Remember to service the blade shaft assembly annually.
RYOBI 1400652 power tool battery(Ni-Cd 12.00V 1400.00mAh)
Source...